The balance application to be followed is as given above.ĭo's: This occurs due to evaporation of water from the solution of soluble salts which rise to the surface. For a smooth surface apply 2 coats of Bison Exterior Putty after Illusion Sealer coat. Apply 2 coats of WeatherCoat Smooth or WeatherCoat All Guard or WeatherCoat Longlife whichever is approved. For exterior apply 1 or 2 coats of Illusion Sealer followed by 1 coat of WeatherCoat Exterior Primer.
On top of that apply 2/3 coats of Silk or Rangoli Easy Clean or Rangoli Fashion Finish or Bison Emulsion as per your choice and budget. Apply 1or 2 coats of 073 Primer and allow it to dry completely. Apply 2 coats of Happy Wall Putty giving overnight interval between the coats. drying time for the surface to dry completely. For interior apply 1 or 2 coats of Illusion Sealer followed by 1coat of 077 Primer. Then wash with soap water(10%) to remove all oiliness as much as possible and rinse with clean soft water. 150/220 to remove all affected old paint film, loose materials, dust, etc. Painting System: Sand the surface with Water Paper no. The affected paint film must be completely removed and the surface has to be given absolutely new face lift. As a result of which paint coatings get burnt and blistered. Painting System: For Interior and Exterior application see 'Brick work'.ĭo's: This refers to surfaces affected by smoke, heat, oil or any water soluble matter. Leave it for curing for minimum 4-5 days. Powder is to be mixed with water in the ratio of Crackfill Powder: Water: 2.5:1. Apply Home Shield Crackfill Paste OR Crackfill Powder with putty knife. On walls where cracks are visible within 5mm of widh & depth, cut the same in "V" shape by.
Exterior paint 2 or 3 coats plus#
It can be repaired by Cement modified mortar using Home Shield Latex Plus Or Advanced Latex Plus and cement in the ratio of Latex Plus: Cement: 1:3 & Advanced Latex Plus: Water: Cement: 1:3:10. If the cracks are visible on the beams and pillars, it is on architectural problem. The main reason is difference in coefficient of expansion of different surfaces. There are many reasons behind these cracking. Secondly, there will be cracks on dissimilar surfaces. When the surface is painted the cracks will often still be visible. In case of a texture application, you can apply exterior texture coating followed by 2 coats of top coat exterior emulsion like WeatherCoat Smooth / WeatherCoat All Guard / Walmasta.ĭo's: These are very fine cracks appearing on bare surfaces or on previously painted surface. This is a waterproofing coating for protecting from –ve water pressure. lf fund permits, you can apply 1 coat of Advanced Latex Plus, Water & cement in the ratio of 1:4:7 before primer. For smooth finish, apply 2 coats Bison Exterior Putty followed by 1 coat WeatherCoat Exterior Primer, followed by 2 coats of Exterior Emulsion. For Exterior walls (after grinding is over) Texture finish can be done the way we do to new walls.
After that apply 2 to 3 coats of finish duly strained through fine cloth and 4 to 6 hrs interval between the coats. Then apply another coat of primer with proper dilution as above and allow it to dry completely. After drying sand the putty lightly with sandpaper no. Then apply 2 coats of Happy wall Acrylic Putty giving overnight interval between the coats. Painting System: For Interior walls (after grinding is over) apply 1 coat of primer with proper dilution and allow it to dry completely. Before doing this all holes must be sealed with Home Shield Latex Plus Or Advanced Latex Plus and cement in the ratio of Latex Plus: Cement: 1:3 & Advanced Latex Plus: Water: Cement: 1:3:10. This will solve the problems of oil layer and will mask the surface roughness. Therefore it is advised to sand the surface with an instrument like a disc sander. Or a thin layer of oil coating on the surface. Holes in a line across the vertical walls.
Exterior paint 2 or 3 coats code#
0 kommentar(er)
